Complete solutions, tailored to your needs Customize →
Home » Anti-Drone Systems » Drone Jammer Modules » 150W and Up » 150W GaN Jamming Module 6900–7200MHz ETLD-JM6972G150

150W GaN Jamming Module 6900–7200MHz ETLD-JM6972G150

150W GaN jamming module ETLD-JM6972G150 covers 6900–7200MHz, DC24–29V, 15A, SMA female, built-in sweep source, 0.55kg.

Application Scenarios: Correctional Facilities, Critical Infrastructure Protection, Event Security, Law Enforcement, Military Defense, VIP Protection
Operating Frequency 6900~7200 MHz
Output Power 150 W
Output VSWR ≤2.0
Operating Voltage DC24V~29V
Dimensions 168 x 584 x 523 mm
Weight 0.55 kg

The 150W GaN jamming module ETLD-JM6972G150 is built for 6900–7200 MHz drone and RF interference tasks. It pairs a high-speed sweep source with GaN output stages. The result is a compact, efficient module that fits fixed or mobile counter-drone systems. If you need a ready-to-integrate RF block, this 150W GaN jamming module gives you power, protection, and simple control in one package.

150W GaN Jamming Module: 6900-7200MHz

Why GaN Matters in a 150W GaN Jamming Module

GaN devices handle high power density better than older silicon parts. They run cooler at the same output, and they tolerate higher voltage swings. That matters in jamming, where duty cycles can be harsh and impedance can shift. The module uses GaN amplifiers to reach 150W while keeping efficiency at 40% or better. The built-in high-speed sweep source covers the full 6900–7200 MHz band, so you do not need an external signal generator. For more on GaN RF basics, see this external GaN overview.

RF Performance and Protection

Output power is 150W typical. Output VSWR stays at ≤2.0, which helps protect the final stage when antennas are not perfect. An internal absorptive VSWR protection device adds another layer of safety. The SMA female output connector is common in lab and field setups. The module is designed for 6900–7200 MHz, a band often used in drone links and specialized communication systems. Always check local rules before transmitting. For RF safety, refer to OSHA RF guidance.

Power, Control, and Thermal Design

The module runs from DC24V to 29V and draws up to 15.0A. A +5V or floating line turns it on; grounding turns it off. That simple logic works with many control boards. Efficiency is ≥40%, so heat still needs a solid mounting plate or heatsink. The 168.5*84.5*23mm case weighs 0.55kg. It is small enough for tight racks but still needs airflow or conduction cooling. Use short, thick DC cables to reduce voltage drop.

Where This Module Fits

This 150W GaN jamming module suits drone detection and countermeasure systems, test benches, and RF research. It can be used as a single-band block or combined with other bands. Because the sweep source is inside, the host system only needs power, control, and an antenna. The module can also support fixed-site protection where directional antennas are used. If you are building a multi-band setup, pair it with our drone jamming module range.

Integration Notes

Keep the antenna match close to 50 ohms. Even though VSWR protection is built in, poor loads reduce effective range and raise heat. Use a DC supply that can deliver 15A continuously with margin. Mount the module on a metal surface. Keep RF cables away from control lines. Test at low duty cycle first, then increase. The switch control is simple, but adding a soft-start sequence can reduce current spikes.

Key Benefits for System Builders

For system builders, the main benefit is fewer external parts. The sweep source, GaN amplifier, and protection are already matched. That saves bench time and reduces cabling mistakes. This 150W GaN jamming module also keeps a standard SMA female output, so it works with many directional antennas. If you need a custom band or higher power, contact us through our internal contact page. We can discuss variants without changing your control interface.

Why Choose ETLD-JM6972G150

The ETLD-JM6972G150 combines a 150W GaN output, 6900–7200 MHz coverage, and a built-in sweep source. It is not just a bare amplifier. It is a compact analog jamming module with protection and control already included. For buyers who want fewer parts and faster deployment, this 150W GaN jamming module is a practical building block.

ParameterSpecificationNotes
Operating Frequency6900~7200 MHzWideband drone/RF band
Output Power150 WTypical output
Output VSWR≤2.050-ohm system
Operating VoltageDC24V~29VRegulated supply
Maximum Operating Current15.0 AAt full output
Efficiency≥40%GaN design
Switch Control+5V or floating = ON / ground = OFFSimple logic
Output ConnectorSMA femaleStandard RF interface
Jamming SourceBuilt-in high-speed sweep sourceNo external generator
VSWR ProtectionBuilt-in absorptive VSWR protection deviceFinal-stage protection
Dimensions168 x 584 x 523 mmLWH
Weight0.55 kgApprox.

What is the ETLD-JM6972G150?

It is a 150W GaN jamming module designed for 6900–7200 MHz operation, with a built-in sweep source and SMA female output.

Does it require an external sweep generator?

No. The high-speed sweep source is already built into the module.

What power supply should I use?

Use a regulated DC24V–29V supply that can deliver at least 15A continuously.

How do I turn the module on and off?

Apply +5V or leave the control line floating for ON. Ground the line for OFF.

What antenna connector is available?

The RF output uses an SMA female connector.

Can it run at 150W continuously?

Continuous operation depends on cooling. Use a metal mounting plate, heatsink, or airflow to manage heat.

Is VSWR protection included?

Yes. The module includes an absorptive VSWR protection device.

What are the size and weight?

The module measures 168.5*84.5*23 mm and weighs approximately 0.55 kg.