Complete solutions, tailored to your needs Customize →
Home » Anti-Drone Systems » Drone Jammer Modules » 150W and Up » 150W GaN UAV Jammer Module 3400-3600MHz ETLD-JM3436G150

150W GaN UAV Jammer Module 3400-3600MHz ETLD-JM3436G150

150W GaN UAV jammer module ETLD-JM3436G150 covers 3400–3600MHz, 150W, DC24–29V, 15A, SMA female, built-in sweep source, 0.55kg.

Application Scenarios: Correctional Facilities, Critical Infrastructure Protection, Event Security, Law Enforcement, Military Defense, VIP Protection
Operating Frequency 3400~3600 MHz
Output Power 150 W
Output VSWR ≤2.0
Operating Voltage DC24V~29V
Maximum Operating Current 15.0 A
Efficiency ≥40%

The 150W GaN UAV jammer module ETLD-JM3436G150 is a compact RF block for 3400–3600 MHz counter-drone and testing work. It combines a GaN amplifier, a high-speed sweep source, and protection circuits in one metal case. You do not need to match separate parts. That saves time and cuts wiring mistakes. The unit is ready for fixed sites, vehicles, and lab benches. It is built for system integrators who need a proven RF block.

150W GaN UAV Jammer Module 3400-3600MHz ETLD-JM3436G150

What This 150W GaN UAV Jammer Module Delivers

GaN technology gives this module high output in a small case. Typical output is 150W across 3400–3600 MHz. Output VSWR stays at ≤2.0, which helps when the antenna is not perfect. The built-in high-speed sweep source means no external signal generator. For general GaN background, see this GaN overview.

RF and Protection Details

The module uses an SMA female output. That is a common interface for lab and field setups. An absorptive VSWR protection device sits inside to guard the final stage. Even with that protection, keep the load close to 50 ohms. Poor matching cuts range and raises heat. Always follow local RF rules. For safety basics, check OSHA RF guidance.

Power and Control Made Simple

Input voltage is DC24V to 29V. Maximum current is 15.0A. A +5V or floating line turns the module on. Grounding it turns the module off. This logic works with most control boards. Use short, thick DC cables. A soft-start circuit can reduce current spikes.

Cooling and Mechanical Fit

Efficiency is ≥40%. That is good for a GaN design, but heat still needs a path out. Mount the 168.5*84.5*23 mm case on metal. Add a heatsink or airflow for long runs. The unit weighs 0.55 kg. It fits tight racks and mobile cases. Do not block the mounting surface.

Integration Scenarios

This 150W GaN UAV jammer module suits fixed sites, vehicle mounts, and test benches. It can run alone or join a multi-band stack. Because the sweep source is inside, your host only needs power, control, and an antenna. For a wider range, see our internal drone jamming modules.

Installation Tips for the 150W GaN UAV Jammer Module

Place the module close to the antenna to reduce cable loss. Use a 50-ohm cable with the right power rating. Keep RF cables away from DC and control lines. Check the antenna VSWR before full power. Start at low duty cycle, then increase slowly. A stable DC supply with 15A margin is important. If the case gets too hot, add a fan or a larger heatsink.

Testing and Maintenance

Run a short test at low power first. Watch current draw and case temperature. A sudden current jump may mean a bad load. Clean the heatsink surface with a dry cloth. Check connectors for tightness. Do not open the housing. The internal sweep source and protection are factory set.

Why Builders Pick This Module

Fewer external parts mean faster builds. The GaN stage, sweep source, and VSWR protection are already matched. The SMA female output works with many directional antennas. If you need a different band or power level, contact us. We can discuss options without changing your control interface.

Final Thoughts

The ETLD-JM3436G150 gives you 150W, 3400–3600 MHz coverage, and a built-in sweep source. It is a ready-to-use analog jamming block. For teams that want less wiring and quicker deployment, this 150W GaN UAV jammer module is a solid choice. Check the datasheet and plan cooling before you deploy.

ParameterSpecificationNotes
Operating Frequency3400~3600 MHzUAV and RF band
Output Power150 WTypical output
Output VSWR≤2.050-ohm system
Operating VoltageDC24V~29VRegulated supply
Maximum Operating Current15.0 AAt full output
Efficiency≥40%GaN design
Switch Control+5V or floating = ON / ground = OFFSimple logic
Output ConnectorSMA femaleStandard RF interface
Jamming SourceBuilt-in high-speed sweep sourceNo external generator
VSWR ProtectionBuilt-in absorptive VSWR protection deviceFinal-stage protection
Dimensions168 x 584 x 523 mmLWH
Weight0.55 kgApprox.

What is the ETLD-JM3436G150?

It is a 150W GaN UAV jammer module for 3400–3600 MHz, with a built-in sweep source and SMA female output.

Does it need an external sweep generator?

No. The high-speed sweep source is already inside the module.

What DC supply should I use?

Use a regulated DC24V–29V supply that can deliver at least 15A continuously.

How do I switch it on and off?

Apply +5V or leave the control line floating for ON. Ground the line for OFF.

What output connector does it have?

The RF output uses an SMA female connector.

Can it run at full power continuously?

Continuous use depends on cooling. Mount it on metal and add a heatsink or airflow.

Is VSWR protection built in?

Yes. It includes an absorptive VSWR protection device.

What are the dimensions and weight?

The module is 168.5*84.5*23 mm and weighs about 0.55 kg.