Multi-Band 30W Drone Jammer Modules Explained
Understand multi-band 30W drone jammer modules: band combinations, total vs per-band power, thermal trade-offs, filtering and antenna design.
Pro 30W Lora FPV jammer module ETLD-JM0809G30 covers 870-960MHz. 30W output, DC24-29V, 3.2A max, SMA female, built-in sweep source.
The 30W Lora FPV jammer module ETLD-JM0809G30 is a compact analog jamming unit for the 870–960MHz band. It combines a GaN amplifier with a built-in high-speed sweep source. That means no external signal generator is needed. You supply DC power and an antenna, and the module handles the rest.

This module targets 870–960MHz. That range is used by LoRa devices, FPV video links, and some remote controls. Output is 30W typical. VSWR is ≤2.0. With a matched antenna, it can disrupt those links while keeping the amplifier within safe limits.
The module runs on DC24–29V and draws up to 3.2A. Efficiency is ≥40%. RF output uses an SMA female connector. It weighs 0.21kg and measures 115.5*46.5*21mm. Those numbers make it easy to fit into portable or fixed builds.
870–960MHz is a crowded slice of sub-1GHz spectrum. Many LoRa and FPV systems rely on it. Targeting this band means you do not waste energy elsewhere. The 30W output gives useful range for fixed sites and mobile kits.
Use a regulated DC supply. A 24V battery works if it holds voltage under load and can deliver 3.2A. Avoid spikes. They can damage the amplifier. For RF safety basics, see the FCC RF Safety Guidelines.
GaN gives this 30W Lora FPV jammer module an efficiency of ≥40%. Less waste heat means smaller enclosures. Still, mount it to metal. Add airflow for long runs. If the case gets too hot, use a heatsink.
Switch control is simple. +5V or floating turns it on. Ground turns it off. That works with microcontrollers and manual switches. The SMA female output is standard for sub-1GHz antennas. Keep coax short. A bad match raises VSWR and cuts range.
The metal case has a small footprint. Use four screws or a clamp. Keep the antenna away from metal surfaces. If you mount it on a drone, watch payload weight. At 0.21kg, it is light, but cabling adds up.
This module suits counter-UAV teams that need a ready 870–960MHz jamming path. Common uses include:
Prison and border protection
Portable inspection units
RF research and testing
Custom anti-drone platforms
Pair it with a detector. The detector finds the drone. The module blocks the link. Need another band? Compare our anti-drone module.
Many jammers need an external signal source. This one does not. The built-in high-speed sweep source saves space and wiring. The DC24–29V input and 3.2A max current are common in vehicle and battery systems. For counter-drone design context, see ITU unmanned aircraft resources. The small housing also helps where rack amplifiers will not fit.
The ETLD-JM0809G30 is a practical building block for 870–960MHz work. It offers 30W output, GaN efficiency, and a built-in sweep source in a small metal case. Confirm your frequency and power needs first. If 870–960MHz is right, this 30W Lora FPV jammer module is ready. Proper grounding, cooling, and antenna choice will get the best results.
| Parameter | Specification | Notes |
| Frequency Band | 870~960MHz | LoRa / FPV band |
| Output Power | 30W | Typical |
| Output VSWR | ≤2.0 | Use matched antenna |
| Working Voltage | DC24V~29V | Regulated DC |
| Max Working Current | 3.2A | At 29V |
| Efficiency | ≥40% | GaN design |
| Switch Control | +5V or floating ON / ground OFF | TTL-friendly |
| Output Connector | SMA female | 50-ohm system |
| Jammer Source | Built-in high-speed sweep source | No external source |
| Dimensions | 115.5*46.5*21mm | Compact housing |
| Weight | 0.21kg | Lightweight |