Complete solutions, tailored to your needs Customize →
Home » Anti-Drone Systems » Drone Jammer Modules » 30W » JM5758G30 30W GaN FPV Jammer Module 5.8 GHz

JM5758G30 30W GaN FPV Jammer Module 5.8 GHz

JM5758G30 30W GaN FPV jammer module: 5750–5850 MHz, DC24–29V, 3.2A max, ≥40% efficiency, SMA female, built-in sweep source, 115.5×46.5×21 mm.

Application Scenarios: Correctional Facilities, Critical Infrastructure Protection, Event Security, Law Enforcement, Military Defense, VIP Protection
Operating Frequency 5750–5850 MHz
Output Power 30 W
Operating Voltage DC24–29 V
Max Operating Current 3.2 A
Efficiency ≥40%
Dimensions 115.5 × 46.5 × 21 mm

The JM5758G30 is a 30W GaN FPV Jammer Module designed for the 5750–5850 MHz band. It combines a GaN RF amplifier, a built-in high-speed sweep source and a compact housing in one unit. For system builders working on authorized counter-drone or RF test projects, it offers a practical way to add 5.8 GHz interference without designing a sweep board from scratch. SMA female output, simple switch control and DC24–29V input make bench integration and field housing installation easier to plan.

JM5758G30 30W GaN FPV Jammer Module, 5.8 GHz

5.8 GHz Focus

The 5750–5850 MHz range is widely used by FPV video links and related 5.8 GHz equipment. The JM5758G30 focuses on this band instead of spreading power across a wider spectrum. That focused design helps integrators match antennas, estimate cable loss and control the RF path. With 30W output and VSWR of 2.0 or lower, the module is intended for setups where antenna quality and heat management are handled properly. A poor load can reduce service life, so check connectors and cables before long runs.

GaN Stage and Current

The amplifier uses GaN devices to deliver 30W in a small package. Efficiency is listed at 40% or higher, which matters when the module sits inside a sealed enclosure. At DC24–29V, maximum current is 3.2A. Actual draw depends on input voltage, temperature and operating conditions. Use a clean power supply with enough headroom, short leads and proper decoupling. Because the housing is compact, mount it to a metal plate or heatsink and monitor temperature during initial tests. Do not rely on free air alone for long transmissions.

Switch and RF Path

Switch control is simple: +5V or floating means on, and grounding means off. This suits remote switching boards, relay logic or manual test fixtures. The RF output is an SMA female connector. Keep the antenna matched to 50 ohms and avoid running the module without a suitable load. The built-in high-speed sweep source saves space and reduces wiring. It also makes the module easier to integrate into portable units, fixed test boxes and OEM housings where an external sweep generator would add cost and complexity.

Duty Cycle and Thermal Planning

Thermal planning is not optional. Run the module at the expected duty cycle while watching current and housing temperature. If temperature climbs quickly, improve the heatsink, lower the ambient temperature or shorten transmissions. A stable installation protects the GaN stage and keeps output consistent over time.

Fit and Installation

At 115.5 × 46.5 × 21 mm and 0.21 kg, the JM5758G30 fits into tight layouts. Plan the RF cable route away from power wires where possible. Leave room for connector access and thermal contact. Use short, low-loss coax at 5.8 GHz; cable loss can quietly cut effective radiated power. The SMA joint should not carry mechanical stress from heavy cables. Support the cable and seal outdoor enclosures against moisture. Before shipping a design, test output, current draw and temperature at the intended duty cycle.

Integration Notes

Typical uses include authorized counter-drone testing, security exercises, RF laboratory work and OEM integration. The module is not a stand-alone product for unlicensed operation. Rules for RF interference vary by country and application. Buyers should confirm that their use, power level, antenna gain and deployment are permitted. The JM5758G30 is a component, not a finished jammer. Final compliance depends on the complete system, including enclosure, antenna, power source and operating procedure.

Design Summary

The JM5758G30 keeps the design focused: 5.8 GHz coverage, 30W GaN output, built-in sweeping and a small footprint. It gives integrators a clear starting point for authorized projects without extra sweep hardware. Check heat, antenna match and power quality first; these three details decide whether the module performs reliably. With proper installation, the 30W GaN FPV Jammer Module can serve as a compact RF building block for controlled counter-FPV setups.

ParameterSpecificationNotes
Operating Frequency5750–5850 MHzFixed 5.8 GHz FPV band
Output Power30 WTypical
Output VSWR≤2.050 Ω load recommended
Operating VoltageDC24–29 VClean supply required
Max Operating Current3.2 AAt rated conditions
Efficiency≥40%Thermal design matters
Switch Control+5 V or floating = ON; ground = OFFSimple logic control
Output ConnectorSMA femaleProtect from cable stress
Jamming SourceBuilt-in high-speed sweep sourceNo external sweep board
Dimensions115.5 × 46.5 × 21 mmCompact housing
Weight0.21 kgApprox.

What is the model number?

It is JM5758G30.

Which frequency range does it use?

It operates from 5750 to 5850 MHz.

How much RF power does it provide?

The typical output is 30 W.

What supply voltage is required?

Use a DC24–29V supply.

How is the module switched?

+5V or floating turns it on; grounding turns it off.

What RF connector is fitted?

It has an SMA female output.

Does it need an external sweep generator?

No. A high-speed sweep source is built in.

What is the maximum current?

Maximum operating current is 3.2 A.

What efficiency is listed?

Efficiency is 40% or higher.

What are the size and weight?

It measures 115.5 × 46.5 × 21 mm and weighs about 0.21 kg.