Complete solutions, tailored to your needs Customize →
Home » Anti-Drone Systems » Drone Jammer Modules » 100W » JM2325G100 100W GaN Anti-Drone Module 2300-2500MHz

JM2325G100 100W GaN Anti-Drone Module 2300-2500MHz

JM2325G100: 100W GaN anti-drone module, 2300–2500MHz, DC24–29V, 12A max, ≥40% efficiency, built-in sweep source and VSWR protection.

Application Scenarios: Correctional Facilities, Critical Infrastructure Protection, Event Security, Law Enforcement, Military Defense, VIP Protection
Working frequency 2300–2500 MHz
Output power 100 W
Working voltage DC 24–29 V
Maximum working current 12.0 A
Efficiency ≥40%
Interference source Built-in high-speed sweep source

Overview

The JM2325G100 is a 100W GaN anti-drone Module for 2300–2500MHz RF suppression and counter-drone systems. It combines a GaN power stage, an internal high-speed sweep source and protection circuits in a compact metal case. It suits integrators who want a tested RF block instead of assembling an amplifier, source and control board from separate parts.

JM2325G100 100W GaN Anti-Drone Module 2300-2500MHz

RF Path

The module covers 2300–2500MHz with 100W output and output VSWR ≤2.0. Its built-in sweep source removes the need for an external signal generator, which reduces cabling and control work. The SMA female output is standard for lab and antenna feeds. Keep the load matched, use rated coax and check connectors before full power. A poor load can reflect energy and raise heat.

Power and Heat

Input is DC24–29V, maximum current 12.0A, and efficiency is ≥40%. That means a fair amount of heat is normal at 100W. Mount the 168.5×84.5×23mm, 0.55kg case on a metal plate with thermal compound and give it airflow. Use short, thick DC leads and a supply that holds voltage under load. If the supply sags, output and stability can suffer.

Control and Protection

A +5V or floating signal turns the module on; grounding turns it off. The internal absorptive VSWR protection helps with mismatch events, but it is not a licence to run without a load. Test the antenna and cable first. Set power gradually and watch current and temperature. Stop if current climbs without output rising.

Integration Notes

Place the module away from sensitive receivers. Use shielded RF paths and keep DC and control lines separated from the RF output. The housing is compact, but it still needs clear airflow and a solid ground. Bench-test at low power, then step up to 100W with a suitable attenuator or load. Do not hot-plug RF connectors.

Applications

Typical uses include counter-drone RF suppression, protected-site testing, RF link denial and integration into mobile or fixed systems. The 100W GaN anti-drone Module can drive suitable antennas, but antenna gain, beamwidth and site rules affect final range. Integrators should confirm local RF regulations, filtering and safety before deployment.

Before Ordering

Confirm your band plan, control logic, supply headroom and cooling. The switch input is simple, so it can be driven by a relay, MCU or manual switch. Check that your antenna covers 2300–2500MHz and handles 100W. If you need monitoring, add external current and temperature sensors. Keep spare connectors and test loads.

Mechanical Notes

The 168.5×84.5×23mm case and 0.55kg weight leave room in many enclosures, but do not block the mounting face. Use all fixing points where possible and clean the mating surface before applying thermal compound. Keep cable bends gentle at the SMA female port. Strain relief on the DC leads avoids pulling the PCB.

Test and Commissioning

Start with a known load or attenuator. Apply DC24–29V within the rated current and confirm the switch logic. Raise drive only after checking current draw and case temperature. Record output at several points across 2300–2500MHz. If output drops or current jumps, stop and inspect the RF path. Repeat the check after final assembly.

Cooling Setup

Do not rely on the case alone. A thin, even layer of thermal compound and a flat metal sink help more than a thick pad. If the anti-drone module sits in a sealed box, bring air over the fins or use a cold plate. Check case temperature after 10–15 minutes at full power. A rising current at steady input is a warning sign.

Summary

The JM2325G100 is a practical 100W GaN anti-drone Module for teams that need 2300–2500MHz output, a built-in sweep source and straightforward on/off control. It is not a finished consumer product; it is an RF building block. Good matching, cooling and supply design matter as much as the power rating.

ParameterSpecificationNotes
Working frequency2300–2500 MHzCovers 2.3 GHz and 2.4 GHz bands
Output power100 WGaN output stage
Output VSWR≤2.0Keep load matched
Working voltageDC 24–29 VCheck supply headroom
Maximum working current12.0 AAt rated operation
Efficiency≥40%Heat removal required
Switch control+5 V or floating = ON; ground = OFFSimple logic input
Output connectorSMA femaleStandard RF interface
Interference sourceBuilt-in high-speed sweep sourceNo external generator needed
VSWR protectionBuilt-in absorptive VSWR protectionHelps with mismatch
Dimensions168.5 × 84.5 × 23 mmL × W × H
Weight0.55 kgModule only

Is the JM2325G100 a complete finished jammer?

No. It is an RF module for system integration. The final enclosure, antenna, filtering and compliance checks remain with the integrator.

Can it run from a 24V battery supply?

Yes, within DC24–29V, but the supply must hold voltage at the 12.0A maximum current. Check cable drop under load.

What antenna should I use?

Use a 2300–2500MHz antenna rated for at least 100W. Match is important; high VSWR will increase heat and may trigger protection.

How is the module switched on?

Apply +5V or leave the control floating for ON. Ground the control for OFF. The input is simple and can be driven by a relay or MCU.

Does it need an external sweep generator?

No. A high-speed sweep source is built in. You only need DC power, control logic and a suitable RF load or antenna.

What cooling is recommended?

Mount it on a flat metal surface with thermal compound and provide airflow or a cold plate. Check case temperature after 10–15 minutes at full power.

What happens if the antenna is disconnected?

Internal absorptive VSWR protection helps with mismatch, but do not use it as a routine no-load test. Always test with a proper load first.

Can the output power be adjusted?

The module is specified as a 100W block. For lower power tests, use an external attenuator or reduce drive/operating time as appropriate.

What connector is on the RF output?

The output uses an SMA female connector. Use rated coax and avoid hot-plugging RF connectors.

Are custom frequency ranges available?

The standard unit is 2300–2500MHz. For other band plans or control options, contact the supplier with your requirements before ordering.