Complete solutions, tailored to your needs Customize →
Home » Anti-Drone Systems » Drone Jammer Modules » 80W » JM0405G80 80W LoRa Jamming Module | 400–500MHz

JM0405G80 80W LoRa Jamming Module | 400–500MHz

JM0405G80 80W LoRa jamming module: 400–500MHz, 24–29V DC, 10A max, ≥40% efficiency, internal sweep/VSWR protection, SMA-F, 168.5×84.5×23mm.

Application Scenarios: Correctional Facilities, Critical Infrastructure Protection, Event Security, Law Enforcement, Military Defense, VIP Protection
Operating Frequency 400–500 MHz
Output Power 80 W
Operating Voltage DC 24–29 V
Max Operating Current 10.0 A
Efficiency ≥40%
Internal Sweep Source High-speed sweep

JM0405G80 is an 80W LoRa Jamming Module for 400–500 MHz. It is delivered as an RF building block, not a finished enclosure. The package contains a GaN output stage, a high-speed sweep source, and absorption-type VSWR protection. You supply DC, control, antenna, and cooling. That last item is not optional. The 168.5 × 84.5 × 23 mm case is compact for 80W, so the mounting surface does real work.

JM0405G80 80W LoRa Jamming Module | 400–500MHz

Bus voltage and current

Run the module from a regulated 24–29V DC supply. Maximum current is 10.0A. Higher bus voltage keeps current lower for the same output, which helps cable and connector choice. Check current at 28V, then repeat near 24V. A supply that sags on sweep peaks can cause reset-like behavior that looks like an RF problem. Use short, thick leads and a clean ground return.

Band context

LoRa plans differ by country. The 400–500 MHz range covers several common low-band allocations, including 433 MHz and 470 MHz areas, plus other narrowband links. That makes JM0405G80 useful for test rigs and fixed sites where one module must cover a broad slice. It does not replace a site survey. Confirm channel use, power limits, and licensing before transmitting. The SMA female output keeps coupler and dummy-load tests simple.

Sweep engine and protection

The internal high-speed sweep source saves an external generator and a cable run. Treat it as a repeatable interference engine, not a lab instrument. The absorption-type VSWR protection helps when an antenna is damaged or a connector is loose. It is not a substitute for a proper load. First power-up should always be on a dummy load, with a current-limited supply and a coupler for power checks.

Enable line behavior

Switch control is +5V or floating for on, ground for off. Floating-on is convenient for remote enable, but it can catch a technician during wiring. Label the harness, and pull the enable line to ground for a safe default. Keep control wires away from the RF output. Verify the ground return before applying 24–29V. A clean enable signal prevents faults that get blamed on the RF stage.

Mounting and heat

At 0.55 kg, the 80W LoRa jamming module needs a flat metal surface, not a plastic standoff. Use thermal paste or a pad. The larger footprint gives more base area than smaller modules, but only if contact is even. Leave clearance for SMA torque and cable bend radius. In sealed boxes, derate output or add airflow. For multi-module racks, use separate DC feeds and sequence power to limit inrush.

Antenna and cable notes

Antenna choice matters more than many buyers expect. A 400–500 MHz antenna with gain and a clean match will outperform a wideband whip with a poor connector. Use coax rated for the band, keep runs short, and weatherproof outdoor joints. Check the match with a analyzer before connecting the module. A borrowed antenna with unknown history is a common cause of high current and unexpected heating.

Commissioning checklist

Start on a dummy load. Record current, output power, and temperature rise. Sweep the band and watch for dropouts or sudden current jumps. Inspect connectors after transport. If the case runs hot, reduce duty cycle before raising output expectations. A short RF path, tight connectors, and a matched antenna solve more problems than late filtering. Keep a baseline record so later checks have a reference.

Where it fits

JM0405G80 suits fixed sites, vehicle mounts, and portable housings that need 400–500 MHz coverage in limited space. Pair it with DC protection, a matched antenna, and a real thermal design. For production, request a test report and confirm connector and control wiring. Do not treat 80W as a continuous guarantee in a sealed enclosure. Derate or cool it, and follow local rules.

ParameterSpecificationNotes
Operating Frequency400–500 MHzCovers common low-band LoRa/ISM allocations
Output Power80 WTypical at rated supply
Output VSWR≤2.0Antenna match should stay within this limit
Operating VoltageDC 24–29 VRegulated supply recommended
Max Operating Current10.0 ASize wiring and protection for continuous draw
Efficiency≥40%Metal thermal path still required
Switch Control+5 V or floating = ONGround = OFF
Output ConnectorSMA femaleUse quality coax and correct torque
Internal Sweep SourceHigh-speed sweepNo external generator required
VSWR ProtectionAbsorption-type deviceHelps with damaged antenna or loose connector
Dimensions168.5 × 84.5 × 23 mmAllow clearance for SMA and cables
Weight0.55 kgFlat metal mounting surface recommended

What frequency range does JM0405G80 cover?

It covers 400–500 MHz, including common low-band LoRa and ISM areas. Confirm local channel plans before use.

Is JM0405G80 a complete jammer?

No. It is an RF module. You still need an antenna, DC protection, control wiring, and thermal design.

What supply voltage and current does it need?

Use a regulated 24–29V DC supply. Maximum current is 10.0A, so leave margin in wiring and protection.

Can it run at 80W continuously?

Treat 80W as a typical rating. In a sealed box, derate output or add airflow.

What happens if the enable pin is left floating?

Floating or +5V turns the module on. Ground the pin to turn it off.

Does the built-in sweep source need programming?

No. It is a fixed high-speed sweep engine. Verify its behavior with a coupler during testing.

What RF connector is fitted?

The output uses an SMA female connector. Use quality coax and correct torque.

Does VSWR protection mean I can test without an antenna?

No. Use a dummy load. Protection reduces risk but does not replace a proper RF load.

How should I mount it for cooling?

Use a flat metal surface with thermal paste or a pad, and leave clearance for SMA and cables.

Do I need a license to use it?

Rules vary by country and application. Check local frequency, power, and licensing requirements before transmitting.