Complete solutions, tailored to your needs Customize →
Home » Anti-Drone Systems » Drone Jammer Modules » 80W » ETLD-JM4850G80 80W GaN Anti-Drone Module 4800–5000 MHz

ETLD-JM4850G80 80W GaN Anti-Drone Module 4800–5000 MHz

80W GaN anti-drone module, 4800–5000 MHz, DC24–29V, 10A, ≥35% efficiency, SMA female, built-in sweep source and VSWR protection.

Application Scenarios: Correctional Facilities, Critical Infrastructure Protection, Event Security, Law Enforcement, Military Defense, VIP Protection
Working Frequency 4800–5000 MHz
Output Power 80 W
Operating Voltage DC 24–29 V
Efficiency ≥35%
Dimensions 168.5 × 84.5 × 23 mm
Weight 0.57 kg

The ETLD-JM4850G80 is an 80W GaN anti-drone module built for systems that need reliable RF power in the 4800–5000 MHz band. It is more than a bare amplifier. The module pairs a GaN output stage with an internal high-speed sweep source, so it works as an analog jamming integrated module for counter-UAV, force protection, and controlled RF testing. It suits builders who want a ready RF core rather than a full finished jammer. If power, cooling, and antenna planning are already in place, this module can shorten the RF chain.

ETLD-JM4850G80 80W GaN Anti-Drone Module 4800–5000 MHz

Why the 4800–5000 MHz Band Matters

Many UAV video links, telemetry channels, and remote-control signals sit around 4.8 GHz and 5.0 GHz. Covering the full 4800–5000 MHz range gives integrators one module for several threats instead of switching between narrowband units. The built-in sweep source also removes the need for an external signal generator in many layouts. That can reduce cabling, save space, and simplify field maintenance. For fixed sites and mobile payloads alike, fewer external parts usually mean fewer failure points.

What the 80W GaN Stage Delivers

GaN devices are chosen for high power density and thermal ruggedness. In this module, typical output is 80W, with output VSWR specified at ≤2.0. Real output can vary with input voltage, load match, temperature, and duty cycle. Do not expect 80W at any input voltage; stay within DC 24–29V. For best results, keep the antenna well matched and avoid running continuously into a poor load. The anti-drone module draws up to 10.0A, and efficiency is ≥35%, so power budgeting and heat removal should be planned from the start.

Control and Protection

Switch control is simple: +5V or floating turns the module on, while grounding turns it off. That makes it easy to drive from a microcontroller, relay, or manual switch. The switch line is not an RF enable; it controls the module’s operation. A built-in absorptive VSWR protection device helps absorb reflected energy when the antenna match is not ideal. This is not a substitute for a good antenna, but it adds a useful layer of protection during real-world use. The RF output uses an SMA female connector, a common choice for compact 50-ohm systems.

Size, Weight, and Integration

At 168.5 × 84.5 × 23 mm and 0.57 kg, the module is small enough for payloads where every gram and millimeter counts. Still, 80W is real power. Mount it on a metal surface when possible, use short and thick DC leads, and leave room for airflow. If the module is used in a sealed enclosure, a heatsink or cold plate is strongly recommended. The power source must handle the 10A peak current without large voltage drops. A stable supply also helps keep the sweep source and output stage behaving predictably.

Typical Applications

Engineers use this class of module in counter-UAV systems, border monitoring, prison security, VIP protection, and RF immunity testing. It can also serve as a bench amplifier when a controlled 4.8–5.0 GHz jamming signal is needed. In testing, use attenuators and shielded loads to avoid interference. Because laws vary by country, the final system must be designed, licensed, and operated according to local regulations. This module is a component, not a finished consumer device.

Before You Design It In

Check the frequency plan, antenna gain, cable loss, cooling, and power source. Confirm that the control logic matches the +5V/ground switching scheme. Remember that the output connector is SMA female, so the mating cable should be SMA male. If you need long cable runs, use low-loss coax; otherwise, output power and VSWR may suffer. If in doubt, start with a lower duty cycle and monitor temperature. With the right RF and thermal design, the ETLD-JM4850G80 offers a compact 80W GaN anti-drone module for demanding 4.8–5.0 GHz projects.

ParameterSpecificationNotes
Working Frequency4800–5000 MHzCovers common 4.8 GHz and 5.0 GHz UAV links; built-in sweep source.
Output Power80 WTypical RF output; actual power depends on voltage, load, and temperature.
Output VSWR≤2.0Keep antenna match within range for stable operation.
Operating VoltageDC 24–29 VRegulated DC input range.
Maximum Current10.0 AAt full load; use adequate wiring and cooling.
Efficiency≥35%Typical under specified conditions.
Switch Control+5 V or floating = ON; ground = OFFLogic-friendly control.
Output ConnectorSMA femaleStandard 50-ohm RF interface.
Jamming SourceBuilt-in high-speed sweep sourceNo external source needed for basic operation.
VSWR ProtectionBuilt-in absorptive VSWR protectionHelps protect the module under poor antenna match.
Dimensions168.5 × 84.5 × 23 mmCompact chassis for payload integration.
Weight0.57 kgLightweight.

What frequency range does this module cover?

It covers 4800 MHz to 5000 MHz, so it can address common 4.8 GHz and 5.0 GHz UAV links.

Is the output power always exactly 80W?

No. 80W is the typical figure. Actual RF output depends on supply voltage, antenna match, temperature, and operating duty cycle.

What power supply should I use?

Use a regulated DC source between 24V and 29V that can deliver at least 10A. Short, thick leads are recommended.

How do I turn the module on?

Apply +5V to the switch pin or leave it floating for ON. Ground the pin for OFF.

Does it include a jamming signal source?

Yes. A high-speed sweep source is built in, so no external sweep generator is required for basic operation.

What connector is on the RF output?

The output is an SMA female connector. Use a suitable 50-ohm SMA male cable or adapter.

How does it handle high VSWR?

It has built-in absorptive VSWR protection. This helps absorb reflected power, but a good antenna match is still important.

What is the physical size and weight?

The module measures 168.5 × 84.5 × 23 mm and weighs 0.57 kg.