1.2GHz 60W Anti-Drone Module: Buyer’s Checklist
A procurement-focused look at 1.2GHz 60W anti-drone modules: band planning, thermal limits, interfaces, test data, and authorized deployment.
60W GaN drone jammer module ETLD-JM2527G60: 2500-2700MHz, DC12-14V, 13A max, ≥40% efficiency, SMA female, built-in sweep source.
60W GaN drone jammer module ETLD-JM2527G60 is a compact RF building block for the 2500–2700MHz band. It packs a 60W GaN output stage and a built-in high-speed sweep source. Integrators can use it for UAV control and video link denial without an external signal generator. The module runs on DC12V–14V and uses a simple +5V or ground switch. Its SMA female output and 138 × 50.5 × 17mm metal housing fit many counter-drone platforms.

This is not a finished jammer; it is a component for professional systems. The ETLD-JM2527G60 takes DC power and a switch signal, then produces a swept 60W signal across 2500–2700MHz. That range covers many drone control, video, and telemetry links. For teams already using our 30W UAV jammer module, this unit adds higher power in a similar form factor.
GaN devices offer high power density and good thermal performance. In this module, the GaN stage delivers 60W typical output with VSWR ≤2.0. The design targets a 50-ohm path, so antenna matching matters. Poor matching raises reflected power and heat. Before full-power tests, check the antenna and use a dummy load. The 2.5–2.7GHz band is widely used, so filtering and power control may be required in some countries. For general RF safety, see FCC RF safety guidelines.
The internal high-speed sweep source moves energy across the band. That creates a wideband interference profile instead of a single tone. For drone links that may use different channels or hopping schemes, sweeping can be more effective than a fixed frequency. The sweep source is already inside the module. The host controller does not need to generate or modulate an RF signal. This saves integration time and reduces parts count. If you need a different band, check our 60W LoRa FPV jamming module.
The module runs from DC12V–14V and draws up to 13A at full load. Efficiency is ≥40%, which helps limit heat compared with lower-efficiency amplifiers. Even so, 60W continuous operation requires a heatsink or metal chassis. Use thermal paste or a thermal pad between the module base and the mounting surface. Keep airflow around the fins. In sealed enclosures, forced air may be necessary. Check current, temperature, and output power after 10–15 minutes of operation.
Switch control is simple: +5V or floating turns the module on; grounding turns it off. This logic works with microcontrollers, relays, or remote switches. The RF output is SMA female. The module measures 138 × 50.5 × 17mm and weighs about 0.22kg. That size fits handheld, vehicle, and fixed-site enclosures. Keep RF cables short and route them away from control lines.
This module is an RF component, not a consumer device. The integrator is responsible for antennas, cooling, power protection, and legal compliance. Jamming rules vary by country. In the United States, for example, the FCC enforces strict rules on jammer use. The 2500–2700MHz band may also include licensed or safety-related services. Test in a shielded room or with a dummy load before going on air.
Common uses include drone control denial, video link disruption, drone detection plus mitigation, border protection, convoy security, and RF research. The module also works as a 60W GaN source for lab testing. Its built-in sweep source makes it practical for teams that want faster deployment and fewer external modules.
The ETLD-JM2527G60 offers 60W GaN output, 2500–2700MHz coverage, an internal sweep source, and a compact metal package. It is a straightforward building block for counter-UAV and high-band RF denial systems. If you need a different band or power level, review our other jammer modules or contact us.
The 60W GaN drone jammer module ETLD-JM2527G60 is designed for engineers who want predictable power, simple control, and a small mechanical footprint. It is a professional RF block for serious integration work.
| Parameter | Specification | Notes |
| Working frequency | 2500–2700MHz | Covers common drone control and video links |
| Output power | 60W | Typical RF output |
| Output VSWR | ≤2.0 | Designed for 50-ohm systems |
| Working voltage | DC12V–14V | Common battery and regulated bus range |
| Maximum current | 13A | At full load |
| Efficiency | ≥40% | Lower heat load |
| Switch control | +5V or floating = ON; grounding = OFF | Simple logic interface |
| Output connector | SMA female | Standard RF interface |
| Jammer source | Built-in high-speed sweep source | No external source required |
| Dimensions | 138 × 50.5 × 17 mm | L × W × H |
| Weight | 0.22 kg | Approx. |