Complete solutions, tailored to your needs Customize →
Home » Anti-Drone Systems » Drone Jammer Modules » 60W » JM3436L60 60W LDMOS Anti-Drone Module | 3.4–3.6GHz

JM3436L60 60W LDMOS Anti-Drone Module | 3.4–3.6GHz

JM3436L60 60W LDMOS anti-drone module covers 3400–3600MHz with 12–14V DC, 12A max, ≥40% efficiency, built-in sweep source, SMA-F, 138×50.5×17mm.

Application Scenarios: Correctional Facilities, Critical Infrastructure Protection, Event Security, Law Enforcement, Military Defense, VIP Protection
Operating Frequency 3400–3600 MHz
Output Power 60 W
Operating Voltage DC 12–14 V
Max Operating Current 12 A
Efficiency ≥40%
Internal Sweep Source High-speed sweep

JM3436L60 is a 60W LDMOS Anti-Drone Module built for 3400–3600 MHz countermeasure links. It combines a solid-state RF chain with an internal high-speed sweep source, so integrators can add DC power, control, and an antenna without designing a separate signal generator. The module is aimed at fixed sites, vehicle mounts, and portable housings where space and heat are tight.

JM3436L60 60W LDMOS Anti-Drone Module | 3.4–3.6GHz

Why LDMOS at 60W

LDMOS gives a good balance between gain, ruggedness, and cost in the 3.4–3.6 GHz range. At 60W, the module can support short- to medium-range jamming tasks while keeping current draw within a 12V–14V platform. Efficiency is listed at ≥40%, which matters when the enclosure is sealed and airflow is limited. The output stage is protected against poor load conditions up to VSWR 2.0, but a clean antenna match still helps stability and service life.

RF and sweep behavior

The built-in high-speed sweep source saves board space and removes external cabling. It is not a full SDR; treat it as a compact interference engine for repeatable wideband coverage. The SMA female output is standard and works with common test loads and directional couplers. Keep the RF path short and use quality coax. If the module sits near a high-power transmitter, add filtering and shielding rather than relying on the housing alone.

Power and switch control

Run the unit from a regulated DC12V–14V supply that can deliver at least 12A continuously. The switch control is simple: +5V or floating means on, grounding means off. That suits remote enable lines and fail-safe shutdown. Use a clean control ground and avoid long unshielded wires near the RF output. During bench tests, current-limited supplies are safer for first power-up.

Mechanical fit

At 138 × 50.5 × 17 mm and 0.22 kg, JM3436L60 fits compact housings and small turret mounts. Use thermal pads or paste to couple the base to a metal plate; do not rely on convection through the case. Leave room for SMA torque and cable bend radius. Mounting hardware should not distort the lid or press on internal boards.

Integration notes

Treat the anti-drone module as one RF block, not a complete jammer. Pair it with a suitable antenna, DC protection, and thermal design. For multi-module racks, separate DC feeds and sequence power to limit inrush. Check the output with a coupler and attenuator before connecting an antenna. Enclosures should allow airflow or external heatsinking, because 60W class devices concentrate heat in a small area.

Testing and deployment

Start with a dummy load and measure current, output power, and temperature rise. Sweep the band to confirm no unexpected dropouts. In the field, keep the antenna matched and inspect connectors after transport. Use short duty cycles when airflow is poor. The 3.4–3.6 GHz band is popular for broadband links, so coordinate frequency use and follow local rules before transmitting.

Heat and wiring checks

Thermal behavior deserves attention. The case is small, so the module will reach steady temperature quickly. A metal chassis with a flat mating surface works better than open air. If you place it in a sealed box, derate output or add a fan. Current draw can rise at lower supply voltage, so set the bench supply to 13.8V for realistic vehicle tests and watch the meter during sweep. Keep the control line clean; a floating input turns the unit on, which may surprise a technician during wiring. Label the harness clearly and pull the control line to ground for a safe default. RF connectors should be torqued to the antenna maker’s value, not over-tightened. After the first hour, check connector temperature and current again. Small changes often show a mismatch before damage occurs.

Summary

JM3436L60 is a practical 60W LDMOS Anti-Drone Module for teams that need a compact 3.4–3.6 GHz RF source with simple switching. It is best used with careful thermal design, a matched antenna, and realistic duty-cycle expectations. For volume builds, request a test report and confirm connector and control wiring before production.

ParameterSpecificationNotes
Operating Frequency3400–3600 MHzCovers the full 3.4–3.6 GHz band
Output Power60 WTypical output at rated supply
Output VSWR≤2.0Keep antenna match within this limit
Operating VoltageDC 12–14 VRegulated supply recommended
Max Operating Current12 ASize wiring and protection for continuous draw
Efficiency≥40%Thermal design still required
Switch Control+5 V or floating = ONGround = OFF
Output ConnectorSMA femaleUse quality coax and correct torque
Internal Sweep SourceHigh-speed sweepNo external signal generator needed
Dimensions138 × 50.5 × 17 mmAllow clearance for SMA and cables
Weight0.22 kgCompact housing support

Can JM3436L60 run from a 12V battery directly?

Yes, within the 12–14V range, but add overvoltage and reverse-polarity protection, and use wiring rated for 12A.

What happens if the switch pin is left unconnected?

The unit turns on because floating or +5V means on. Tie the pin to ground for off.

Is an external sweep generator required?

No. The module includes an internal high-speed sweep source.

What antenna connector is fitted?

It uses an SMA female connector. Use a matched antenna and correct torque.

How much heat should I expect?

At ≥40% efficiency, a significant part of the input power becomes heat. Metal mounting and airflow help.

Can I combine several modules?

Yes, but use separate DC feeds, power sequencing, and a proper RF combining design. Avoid simple splitters.

What supply current should I budget?

Plan for at least 12A continuous plus margin. Lower supply voltage can increase current draw.

Does VSWR ≤2.0 mean no antenna tuning is needed?

It is a limit, not a target. A better match improves stability and service life.

Is it safe to test without an antenna?

Use a dummy load or attenuator. Do not run an open output for extended periods.

What is the operating band?

3400–3600 MHz. Coordinate frequency use and follow local regulations before transmitting.