Complete solutions, tailored to your needs Customize →
Home » Anti-Drone Systems » Drone Jammer Modules » 60W » ETLD-JM0101L60 60W LDMOS UAV Jammer Module 135–175MHz

ETLD-JM0101L60 60W LDMOS UAV Jammer Module 135–175MHz

ETLD-JM0101L60 60W LDMOS jammer module: 135–175MHz, DC12–14V, 12A max, ≥40% efficiency, SMA female, built-in high-speed sweep source.

Application Scenarios: Correctional Facilities, Critical Infrastructure Protection, Event Security, Law Enforcement, Military Defense, VIP Protection
Working frequency 135–175 MHz
Output power 60W
Working voltage DC12V–14V
Maximum current 12A
Efficiency ≥40%
Output connector SMA female

The ETLD-JM0101L60 is a 60W LDMOS jammer module for the 135–175 MHz VHF band. It is made for system integrators who need a self-contained RF block rather than a bare amplifier. Inside the housing, a high-speed sweep source feeds the LDMOS output stage. That means the host system only has to supply DC power and a simple on/off logic signal. The module is suited to UAV countermeasure work and remote control denial. Its SMA female output and compact body fit rugged enclosures.

ETLD-JM0101L60 60W LDMOS UAV Jammer Module 135–175MHz

Why LDMOS for this band?

LDMOS has a long history in VHF and UHF power design. It is rugged, well understood, and relatively tolerant of load mismatch. In the 135–175 MHz range, a 60W LDMOS stage can deliver solid output without the cost and complexity of some higher-frequency technologies. The module’s ≥40% efficiency helps keep current draw and heat within practical limits for vehicle, portable, and fixed installations. The supply range is DC12V–14V, which matches common battery and regulated bus systems. At full output, maximum current is 12A, so wiring and fusing should be sized with margin.

Band coverage and sweep source

The 135–175 MHz band is used by many legacy remote controls, telemetry links, and low-band drone control paths. The built-in high-speed sweep source moves across the band continuously. This creates a wideband interference profile rather than a single narrow tone. For counter-UAV use, that can be more effective against frequency-hopping or wideband links. It also saves space and cost because no external signal generator is required. The sweep rate and pattern are set inside the module; the user does not need to program a source.

Power and matching

Output power is typically 60W. The module is designed for a 50-ohm RF path, and output VSWR is specified at ≤2.0. A well-matched antenna is important. High reflected power will reduce reliability and can damage the output stage over time. Before running full power, check the antenna with a VSWR meter or network analyzer. A dummy load is strongly recommended for first power-up. Keep coaxial cables short and use connectors rated for the power level.

Control logic

The switch control is simple: +5V or floating turns the module on, while grounding turns it off. This interface is easy to drive from a microcontroller, relay board, or remote switch. The control pin should not be exposed to voltages above the logic level. If the host uses an open-drain output, it can pull the pin low for off and release it for on. Add a series resistor if the control line runs near RF or noisy power cables.

Mechanical and thermal notes

The 60W LDMOS jammer module measures 138 × 50.5 × 17 mm and weighs about 0.22 kg. Its flat metal base is intended to transfer heat into a chassis or heatsink. Do not run 60W continuously with the module sitting in free air. Use thermal paste or a thermal pad between the module and the mounting surface. Keep the heatsink fins clear. In enclosed cases, forced air may be needed. Vibration and shock are also worth considering for vehicle or drone-mounted systems.

Integration and compliance

This is a component, not a finished jammer. The integrator is responsible for antennas, power protection, cooling, and legal compliance. RF output limits and jamming rules vary by country. The 135–175 MHz band includes licensed and safety-related services in some regions, so filtering and power control may be required. Always test in a shielded environment or with a dummy load before going on air.

Typical applications

Common uses include low-band UAV jamming, remote control denial, border and facility protection, convoy security, and RF research. The drone jammer module also works as a 60W LDMOS source for VHF testing. Its internal sweep source makes it a practical choice for teams that want faster integration and fewer external parts.

Final thought

The ETLD-JM0101L60 delivers 60W LDMOS output, built-in sweeping, and a compact mechanical package for the 135–175 MHz band. It is a straightforward RF building block for professional counter-drone and VHF denial systems.

ParameterSpecificationNotes
Working frequency135–175 MHzCovers low-band VHF UAV and remote control links
Output power60WTypical RF output
Output VSWR≤2.0Designed for 50-ohm systems
Working voltageDC12V–14VCommon battery and regulated bus range
Maximum current12AAt full load
Efficiency≥40%Lower heat load
Switch control+5V or floating = ON; grounding = OFFSimple logic interface
Output connectorSMA femaleStandard RF interface
Jammer sourceBuilt-in high-speed sweep sourceNo external source required
Dimensions138 × 50.5 × 17 mmL × W × H
Weight0.22 kgApprox.

What is the operating band?

The module covers 135–175 MHz.

How much RF power does it produce?

It delivers around 60W typical output.

What supply voltage is needed?

Use a DC12V to DC14V supply.

Does it include a sweep generator?

Yes, a high-speed sweep source is built inside.

What connector is on the RF output?

The output uses an SMA female connector.

How is on/off controlled?

+5V or floating turns it on; grounding turns it off.

What is the current draw at full power?

It can draw up to 12A.

Can it be used outdoors?

Only when mounted inside a suitable weatherproof enclosure.