What Is an 80W Jammer Module Used For?
An 80W jammer module is used in authorized counter-drone systems to disrupt specific RF links. Here is where it fits, and how to scope one.
80W GaN UAV jamming module, 5600–5900MHz, DC24–29V, 10A, ≥35% efficiency, SMA female, built-in sweep source and VSWR protection.
The ETLD-JM5659G80 is an 80W GaN UAV jamming module designed for the 5600–5900 MHz band. It combines a GaN power stage with an internal high-speed sweep source. That makes it an analog jamming integrated module, not just a plain amplifier. It is aimed at counter-UAV systems, fixed-site protection, and RF test benches. If your enclosure, antenna, and power design are ready, this module can serve as the RF core.

Many UAV links use 5.8 GHz for video, control, or telemetry. Covering 5600–5900 MHz gives one module enough range for several real-world threats. The built-in sweep source also cuts the need for an external signal generator in many builds. Fewer external boxes mean less cabling and simpler maintenance. For mobile or fixed installations, that can be a practical advantage.
The module uses GaN devices for high power density and thermal strength. Typical output is 80W. Output VSWR is specified at ≤2.0. Actual RF power will change with supply voltage, load match, temperature, and duty cycle. It is not guaranteed at every input voltage. Keep DC input between 24V and 29V. A well-matched antenna will help you get the most from the module. Maximum current is 10.0A, and efficiency is ≥35%. Plan for heat removal from the start.
Switch control is simple. Apply +5V or leave the pin floating to turn the module on. Ground the pin to turn it off. This works well with microcontrollers, relays, or manual switches. The control pin is not an RF input. A built-in absorptive VSWR protection device helps absorb reflected energy when the antenna match is poor. It adds protection, but it does not replace a good antenna. The RF output is SMA female, a common 50-ohm interface for compact systems.
The UAV jamming module measures 168.5 × 84.5 × 23 mm and weighs 0.57 kg. That size suits payloads where space and weight matter. But 80W is real power. Mount the module on metal when possible. Use short, thick DC cables. Leave room for airflow. In a sealed case, use a heatsink or cold plate. The power supply must handle 10A peaks without a large voltage drop. Stable DC input also helps the sweep source and output stage stay predictable.
Common applications include counter-UAV systems, border monitoring, prison security, VIP protection, and RF immunity testing. The module can also work as a bench amplifier when a controlled 5.6–5.9 GHz jamming signal is needed. During testing, use attenuators and shielded loads to limit interference. Rules differ by country. The final system must be designed, licensed, and operated under local regulations. This is a component, not a finished consumer product.
Check frequency plan, antenna gain, cable loss, cooling, and DC supply. Confirm that the control logic matches the +5V/ground switching scheme. The output is SMA female, so use an SMA male mating cable. For long runs, choose low-loss coax. Otherwise, output power and VSWR may suffer. If unsure, start at a lower duty cycle and watch temperature. With proper RF and thermal design, the ETLD-JM5659G80 offers a compact 80W GaN UAV jamming module for 5.6–5.9 GHz projects.
Do not run the module without a load. Even with built-in protection, a missing or badly matched antenna can stress the output stage. Start with a known-good 50-ohm load for bench checks. Then move to the real antenna and confirm VSWR. Monitor current, temperature, and output power during the first run. If any value drifts, stop and check the setup. Small mistakes in cooling or cabling can shorten module life.
| Parameter | Specification | Notes |
| Working Frequency | 5600–5900 MHz | Covers common 5.8 GHz UAV links; built-in sweep source. |
| Output Power | 80 W | Typical RF output; depends on voltage, load, and temperature. |
| Output VSWR | ≤2.0 | Keep antenna match within range for stable operation. |
| Operating Voltage | DC 24–29 V | Regulated DC input. |
| Maximum Current | 10.0 A | At full load; use proper wiring and cooling. |
| Efficiency | ≥35% | Typical under specified conditions. |
| Switch Control | +5 V or floating = ON; ground = OFF | Logic-friendly control. |
| Output Connector | SMA female | Standard 50-ohm RF interface. |
| Jamming Source | Built-in high-speed sweep source | No external source needed for basic operation. |
| VSWR Protection | Built-in absorptive VSWR protection | Helps protect under poor antenna match. |
| Dimensions | 168.5 × 84.5 × 23 mm | Compact for payload integration. |
| Weight | 0.57 kg | Lightweight for portable or airborne use. |