20W Anti-Drone Module Price: What Drives Cost?
Understand 20W anti-drone module price factors, from RF bands and cooling to enclosure, compliance and order volume. Compare quotes wisely.
This 20W GaN jamming module ETLD-JM5758G20 covers 5725-5850MHz with 20W output, DC24-29V, 2.5A max, SMA female, and a built-in sweep source.
If you need a compact jamming path for the 5.8GHz band, the 20W GaN jamming module ETLD-JM5758G20 is worth a look. It covers 5725–5850MHz and packs a built-in sweep source. That means no external oscillator. You supply DC power and an antenna, and the module does the rest.

This is an integrated analog jammer, not just an amplifier. The 5725–5850MHz range is used by many drones for video and control. Output is 20W typical. VSWR is ≤2.0. With a matched antenna, it can disrupt those links while keeping the amplifier safe.
The module runs on DC24–29V and draws up to 2.5A. Efficiency is ≥40%. RF output is SMA female. It weighs 0.21kg and measures 115.5*46.5*21mm. Those numbers make it easy to fit into portable or pole-mounted builds.
5725–5850MHz is a crowded slice of 5.8GHz. Many consumer drones use it. Targeting this band means you do not waste energy elsewhere. The 20W output gives useful range for fixed sites and mobile kits.
Use a regulated DC supply. A 24V battery works if it holds voltage under load and can deliver 2.5A. Avoid spikes. They can kill the amplifier. For RF safety basics, see the FCC RF Safety Guidelines.
GaN gives this 20W GaN jamming module an efficiency of ≥40%. Less heat means smaller enclosures. Still, mount it to metal. Add airflow for long runs. If the case gets too hot, use a heatsink.
Switch control is simple. +5V or floating turns it on. Ground turns it off. That works with microcontrollers and manual switches. The SMA female output is standard for 5.8GHz antennas. Keep coax short. A bad match raises VSWR and cuts range.
The metal case has a small footprint. Use four screws or a clamp. Keep the antenna away from metal surfaces. If you mount it on a drone, watch payload weight. At 0.21kg, it is light, but cabling adds up.
Choose a 50-ohm antenna for 5725–5850MHz. A directional panel or horn works for fixed sites. For mobile use, an omni antenna may be better. Check VSWR before full power. A poor match can damage the module.
Do not use an unregulated supply. Voltage above 29V may harm the unit. Use a fuse. Keep wires short. If you run from a vehicle, add filtering to reduce alternator noise.
This module fits counter-UAV teams that need a ready 5.8GHz jamming path. Common uses:
Prison and airport protection
Portable inspection units
RF research
Custom anti-drone platforms
Pair it with a detector. The detector finds the drone. The module blocks the link. Need another band? Compare our other drone jammer modules.
Many jammers need an external signal source. This one does not. The built-in high-speed sweep source saves space and wiring. The DC24–29V input and 2.5A max current are common in vehicle and battery systems. For counter-drone design context, see ITU unmanned aircraft resources. The small housing also helps where rack amplifiers will not fit.
The ETLD-JM5758G20 is a practical building block for 5725–5850MHz work. It offers 20W output, GaN efficiency, and a built-in sweep source in a small metal case. Confirm your frequency and power needs first. If 5725–5850MHz is right, this 20W GaN jamming module is ready. Proper grounding, cooling, and antenna choice will get the best results.
| Parameter | Specification | Notes |
| Frequency Band | 5725~5850MHz | 5.8GHz UAV band |
| Output Power | 20W | Typical |
| Output VSWR | ≤2.0 | Use matched antenna |
| Working Voltage | DC24V~29V | Regulated DC |
| Max Working Current | 2.5A | At 29V |
| Efficiency | ≥40% | GaN design |
| Switch Control | +5V or floating ON / ground OFF | TTL-friendly |
| Output Connector | SMA female | 50-ohm system |
| Jammer Source | Built-in high-speed sweep source | No external source |
| Dimensions | 115.5*46.5*21mm | Compact housing |
| Weight | 0.21kg | Lightweight |